LG Error Codes, A Clear Map of CH Faults

When an LG split system detects a problem, it usually announces it with CH followed by a number.

That short code is your best starting point for working out what went wrong. This page brings the common LG error codes together in one place, explains how to read them and points you to a detailed guide for each, so you know what is safe to try and when to call a technician.

How does an LG show its error codes?

Most LG wall units with a numeric display show the letters CH followed by two digits, sometimes alternating with the set temperature. Some models flash an indicator light in a pattern instead, with long and short blinks representing the digits. Ducted and cassette systems with wired controllers often show the code on the controller screen. Connected models may report faults through the LG ThinQ app as well.

If you are unsure how your model displays codes, our how to check LG error code guide walks through each method. Write the code down or take a photo before switching off, since some codes clear once power cycles.

Which LG codes appear most often?

The table below lists the codes covered on this site, grouped by the part of the system they relate to. Each one has its own detailed page, linked in the sections that follow.

CodeUsual meaningGroup
CH01Room air sensor faultIndoor sensors
CH02Indoor coil inlet sensor faultIndoor sensors
CH06Indoor coil outlet sensor faultIndoor sensors
CH09Indoor EEPROM memory faultIndoor electronics
CH10Indoor fan motor faultFans
CH67Outdoor fan lockFans
CH05Indoor and outdoor communication faultCommunication
CH21DC peak or IPM faultPower electronics
CH22Compressor or input overcurrentPower electronics
CH23DC link low voltagePower electronics
CH27Power factor correction faultPower electronics
CH26Compressor position faultCompressor
CH29Compressor phase overcurrentCompressor
CH32High discharge temperatureHeat protection
CH61Condenser coil overheatHeat protection
CH62Inverter heat sink overheatHeat protection
CH38Low refrigerant or leakRefrigerant
CH44Outdoor air sensor faultOutdoor sensors
CH45Condenser pipe sensor faultOutdoor sensors

Meanings can vary slightly between model series, so always check your manual or ask a technician to confirm.

Which codes relate to sensors?

Sensors are small thermistors that tell the boards about temperatures around the system. When one fails or its wiring breaks, the board receives impossible readings and stops.

Indoor sensor codes include CH01 for the room air probe, CH02 for the coil inlet probe and CH06 for the coil outlet probe. Outdoor sensor codes include CH44 for the outdoor air probe and CH45 for the condenser pipe probe.

Sensor faults are usually among the more modest repairs. The part itself is inexpensive, and testing is quick with a meter. The main variables are access and whether wiring damage extends further than the probe.

Which codes concern the fans?

Two codes cover fan problems. CH10 points to the indoor fan motor, often linked to grime on the fan barrel, worn bearings or a failed motor. CH67 points to the outdoor fan, frequently caused by debris, worn bearings or a failed motor.

Fan faults show up clearly in how the system feels. With CH10, little air comes from the indoor head. With CH67, air flows indoors but it is neither cool nor warm.

What does the communication code mean?

CH05 tells you the indoor and outdoor boards stopped hearing each other. Loose terminals, damaged cables, power supply problems and board faults are all possible causes. Storms and pests are common triggers. Because the fault can be intermittent, keeping notes on when it appears helps the technician.

Which codes involve the power electronics?

The outdoor inverter board converts household power into the variable supply that drives the compressor. Several codes protect this board.

  • CH21 responds to sudden current peaks in the power module.
  • CH22 responds to excessive input or compressor current.
  • CH23 reports low DC link voltage.
  • CH27 reports a power factor correction fault.

These codes overlap in their causes. Supply problems, dirty coils, weak fans, board ageing and compressor faults can all play a part. Careful testing separates them.

Which codes point at the compressor?

CH26 means the drive could not detect the compressor rotor position, often at start up. CH29 means one or more compressor phases drew too much current. Neither code automatically means a dead compressor. Wiring, terminals, inverter boards and operating conditions are frequent causes, so testing comes before any major replacement.

Which codes warn about heat?

Three codes protect against overheating in different places.

  • CH32 watches compressor discharge temperature.
  • CH61 watches the outdoor coil temperature.
  • CH62 watches the inverter heat sink.

These codes often share causes, such as a dirty condenser coil, poor clearance, a weak outdoor fan or low refrigerant. Owners can sometimes help by clearing debris and improving airflow around the condenser unit.

What about refrigerant?

CH38 indicates low refrigerant or a suspected leak. The system infers this from sensor readings, so testing confirms whether gas is actually low. A proper repair involves finding and fixing the leak, then refilling by weight. Our LG aircon regas Sydney page explains the process.

What should you do as soon as a code appears?

A calm, simple routine works for most codes.

  • Note the code and take a photo of the display.
  • Switch the system off at the remote.
  • Check for obvious issues, such as a tripped breaker, blocked outdoor unit or dirty filters.
  • Turn off power at the breaker for a few minutes, then restore it.
  • Restart once and watch whether the code returns.
  • If it returns, leave the system off and book a visit.

Our LG reset guide explains the power cycle in detail. Never open the indoor head or condenser unit beyond removing the filters.

Why do some codes appear together?

Faults often trigger more than one protection. A dirty outdoor coil can raise pressure, current and temperature at once, so CH22, CH32 and CH61 might all appear over a few days. Low refrigerant can show as CH38 and later as CH32. A failing power factor stage can pull the DC link down, showing CH27 and CH23 together. Seeing a combination is useful information, so record every code you notice.

Can a code vanish and then return?

Yes. Some faults are intermittent. A loose terminal may connect when cool and fail when warm. A sensor lead may break only when the wind moves it. Moisture may cause trouble only after rain. If a code clears and returns, keep a log of the date, time, weather and what the system was doing. That record helps the technician find the pattern.

How do multi split systems display codes?

On multi split systems, one condenser unit serves several indoor heads. Outdoor faults often show on every head, while indoor faults show only on the affected room. That difference helps narrow the cause. If only one head shows CH05, for example, the problem likely sits on that branch rather than in the condenser unit.

Do meanings differ across LG models?

Most core codes stay consistent across LG residential split systems, yet some series use additional or slightly different codes. Ducted, cassette and multi split systems may also use specific codes for zone controllers or addressing. When in doubt, check the manual for your model or share the code and model number with a technician.

What happens during a diagnostic visit?

The technician starts by confirming the code and asking about symptoms and timing. Then they inspect the relevant parts, test sensors, wiring, fans and boards, and measure pressures or current as needed. Once they identify the cause, they explain it and provide a quote before any repair. Our LG AC repair Sydney page describes a typical visit.

Which codes can owners influence?

Owners cannot repair sensors, boards or refrigerant circuits, but they can help with codes linked to airflow and cleanliness. Clearing debris from around the condenser unit, rinsing filters and keeping the coil clean can prevent or resolve some cases of CH61, CH62, CH22 and CH67. Our LG outdoor unit check and LG clean filters guides show how.

Which codes are usually modest repairs?

Sensor faults such as CH01, CH02, CH06, CH44 and CH45 are typically modest. Fan faults depend on whether the job calls for cleaning or a new motor. Board related codes cost more, and compressor replacement sits at the top. Our LG AC repair cost Sydney page explains what drives the bill.

Should you keep a record of past codes?

It helps a great deal. A simple note of each code, its date and what was done builds a history for your system. Over time, it can reveal patterns, such as heat related codes every summer, that point to a lasting fix like better shade or a regular coil clean.

How urgent is each group of codes?

Not every code carries the same urgency. As a rough guide, consider these groupings, while remembering that any repeating code deserves attention.

Act promptly

Codes involving heat, current or refrigerant, such as CH21, CH22, CH29, CH32, CH38, CH61 and CH62, protect expensive parts. Leaving them unresolved or forcing restarts risks damage to the compressor or inverter board. Switch off after one restart attempt and book a visit.

Book soon

Fan codes, communication faults and power supply codes, including CH05, CH10, CH23, CH27 and CH67, stop the system but usually do not cause further harm if it stays off. Book a visit soon so you are not without cooling or heating for long.

Plan a visit

Sensor and memory codes, such as CH01, CH02, CH06, CH09, CH44 and CH45, also stop the system, yet they are typically simple to fix. Book a visit at a convenient time and keep the system off meanwhile.

What do the codes look like on a blinking light?

Models without a numeric display often show codes through an indicator light. Typically, a series of long blinks represents the tens digit and a series of short blinks represents the units digit, followed by a pause before the pattern repeats. For example, two long blinks followed by one short blink would represent CH21. Patterns can vary by model, so check your manual. If counting proves tricky, take a short video and count the blinks afterwards.

Do codes appear more after power cuts?

Yes, some do. Storms and blackouts can glitch boards, corrupt memory or damage sensitive components. CH05, CH09, CH21, CH23 and CH27 are among the codes that sometimes appear after power disturbances. A single reset often clears glitches. If a code persists after the reset, surge damage becomes more likely, and a technician should test the boards.

What about new installations?

Codes that appear within days of installation usually point to installation issues rather than worn parts. Wiring errors can show as CH05, while refrigerant problems from poor evacuation or incorrect charge may show as CH38 or CH32. Contact the installer first, since workmanship warranties typically cover these problems.

LG error codes, getting help

LG error codes give you a head start in understanding what your system needs. Use the guides linked above to learn what each code means, try the safe steps and book a technician when a code returns.

A clean outdoor unit is one of the best defences against hot weather trouble.

If you hear a new sound, try to note whether it comes from inside or outside.

Clear communication with the technician leads to better outcomes for everyone.

Small investments in care today often prevent larger repairs tomorrow.

Following a safe, step by step approach avoids accidental damage to the system.

Call 02 9071 1142 or use our booking page to arrange an LG technician.

Frequently asked questions

How do I read an LG error code?

Look for CH followed by two digits on the display, or count the indicator light blinks.

Will resetting clear an LG error code?

Sometimes. If the code returns after one power cycle, book a technician.

Are LG codes the same on every model?

Most core codes are consistent, but some series use extra codes.

Which LG codes relate to heat?

CH32, CH61 and CH62 protect against overheating.

Which code means low gas?

CH38 generally indicates low refrigerant or a leak.

Can the ThinQ app show codes?

Many connected models report faults through the app.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://lg.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, LG Service”,”url”:”https://lg.sydneyaircare.com.au/”,”description”:”LG air conditioner repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with LG.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”How do I read an LG error code?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Look for CH followed by two digits on the display, or count the indicator light blinks.”}},{“@type”:”Question”,”name”:”Will resetting clear an LG error code?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Sometimes. If the code returns after one power cycle, book a technician.”}},{“@type”:”Question”,”name”:”Are LG codes the same on every model?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Most core codes are consistent, but some series use extra codes.”}},{“@type”:”Question”,”name”:”Which LG codes relate to heat?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”CH32, CH61 and CH62 protect against overheating.”}},{“@type”:”Question”,”name”:”Which code means low gas?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”CH38 generally indicates low refrigerant or a leak.”}},{“@type”:”Question”,”name”:”Can the ThinQ app show codes?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Many connected models report faults through the app.”}}]}
Call 02 9071 1142