LG CH29 Error, Uneven Current Across the Compressor Phases
An inverter compressor runs on three separate streams of current, each feeding a different winding.
The LG drive watches all three closely. When one or more climbs far above normal, the board stops the compressor and shows the LG CH29 error. The cause might be electrical, mechanical or environmental. This page explains the possibilities and the steps a technician takes to sort them out.
What does the LG CH29 error mean?
LG service material commonly describes CH29 as a compressor phase overcurrent error. The inverter board converts the DC link into three alternating outputs, called phases, that drive the three windings of the compressor motor. Sensors on the board measure current in these outputs. If current in any phase exceeds a threshold, the board halts the compressor to protect the windings and the power module, then records CH29.
Because CH29 looks at the output side, it often points toward the compressor, its wiring or the final stage of the inverter, rather than the household supply.
What are compressor phases?
Think of a three phase motor as three people pushing a merry go round in turn. Each pushes at a slightly different moment, so the ride turns smoothly. If one person suddenly pushes much harder than the others, or pushes at the wrong time, the ride jerks and strains.
In the compressor, the inverter times the current in each winding so the rotor turns smoothly. When one winding carries far more current than the others, something is out of balance. That imbalance might come from a damaged winding, a poor connection, a failing switch in the power module or a compressor that is mechanically struggling.
What symptoms come with CH29?
Owners usually see one or more of these.
- The condenser unit starts, runs briefly and stops with a click.
- A rough hum or vibration comes from the compressor before it stops.
- The fault repeats at almost every start attempt.
- Breakers trip occasionally during compressor start.
- The code appears more in very hot weather or under heavy load.
- Other drive codes such as CH21 or CH26 have also appeared.
Make a note of timing and conditions, since they help separate electrical from mechanical causes.
Which faults commonly cause CH29?
Compressor winding damage
If insulation within a winding breaks down, part of the winding may short to another turn or to the casing. Current in that phase rises sharply. Winding damage can follow overheating, moisture in the system or age.
Loose or burnt compressor terminals
The three compressor wires connect to terminals on top of the compressor. Vibration and heat can loosen these connections over time, causing arcing and uneven current. Burnt terminals often show discolouration or melted insulation.
Power module faults
The power module contains six switching devices that create the three phases. If one degrades, the phase it controls may carry abnormal current. Surge damage is a common cause.
Mechanical strain
A compressor that is partly seized, has worn bearings or is fighting liquid refrigerant requires more torque. That extra effort shows up as higher current, sometimes unevenly across phases.
Abnormal operating conditions
Very high pressures from a dirty condenser coil, a failing outdoor fan or refrigerant overcharge raise compressor load. While this usually raises current evenly, it can push a marginal phase over the limit first.
Faulty current sensing
Occasionally, the circuit that measures phase current on the board fails and reports a high value that is not real.
What can an owner safely check?
The compressor and inverter board are off limits for owners, yet a few safe steps help.
- Switch the system off at the remote and at the circuit breaker.
- Wait several minutes before restoring power.
- Check that the condenser coil is not blocked by leaves or debris.
- Make sure nothing restricts airflow around the condenser unit.
- Restart once and listen to the outdoor unit from a safe distance.
If CH29 returns, leave the system off and book a visit. Repeated starts with a phase fault can damage the power module further. Our LG reset guide explains the safe restart.
How does a technician diagnose CH29?
The technician starts by making the system safe and discharging the inverter board. Then they inspect the compressor terminal cover, wires and connectors for heat damage, looseness or corrosion.
Next, they measure winding resistance between each pair of compressor terminals. Healthy windings show nearly identical readings. A noticeable difference suggests winding damage. They also measure insulation resistance from each terminal to the compressor body. A low reading indicates insulation breakdown.
After that, they test the power module switching devices. A short or open device confirms an inverter fault. If static tests look normal, they may run the compressor while measuring current in each phase with a clamp meter, comparing those readings with what the board reports.
Finally, they review operating conditions, including pressures, coil cleanliness and fan performance, to see whether excessive load contributed.
Which repairs typically clear CH29?
| Finding | Typical repair |
|---|---|
| Loose or burnt terminals | Repair wiring and replace terminals |
| Faulty power module | Replace the outdoor inverter board |
| Shorted or earthed winding | Replace the compressor |
| High load from dirty coil or weak fan | Clean coil, repair fan, then retest |
| Refrigerant overcharge | Recover and weigh in the correct charge |
| Faulty current sensing | Replace the outdoor board |
After the repair, the technician runs the compressor through its speed range and checks phase currents for balance.
Is CH29 always a compressor failure?
No. Terminals and inverter boards fail far more often than many people expect, and both are less costly to fix than a compressor. Careful testing separates these possibilities. A good technician will only recommend compressor replacement after checking windings, insulation and connections.
How do you tell a winding fault from a board fault?
The key lies in testing the compressor independently of the board. Winding resistance and insulation tests look at the compressor alone. If those readings are healthy, the compressor is probably fine and attention turns to the board. If they show imbalance or low insulation, the compressor has a problem regardless of the board.
Some technicians also use a dedicated compressor tester that drives the motor without the inverter board. If the compressor runs smoothly on the tester, the board is the likely culprit.
Why does CH29 appear more in hot weather?
High outdoor temperatures increase system pressures and compressor load. Current rises in every phase. A small imbalance that stays below the limit on mild days may cross it during a heatwave. If your LG shows CH29 mainly on the hottest afternoons, that pattern suggests a marginal component or excessive load rather than a sudden failure.
How does CH29 relate to CH21 and CH22?
These codes all involve current in the compressor drive. CH21 responds to instant peaks in the power module, CH22 to excessive input or compressor current and CH29 to current in individual output phases. Because they share many causes, they often appear together or in sequence. Our LG CH21 error and LG CH22 error pages explain the related codes.
Can refrigerant problems cause CH29?
Yes, indirectly. Liquid refrigerant entering the compressor creates a sudden mechanical load. An overcharged system raises pressures and current. A system with air or moisture inside behaves similarly. Each can stress the compressor and push phase current up. During diagnosis, the technician checks pressures and temperatures to rule these out. Our LG aircon regas Sydney page explains correct refrigerant handling.
When is compressor replacement worth it?
If testing confirms damaged windings or a seized compressor, replacement is the fix. On newer systems, it often makes sense. On older systems with other worn parts, it may be worth weighing replacement of the whole system instead. The technician should outline both options honestly. Our LG AC repair cost Sydney page explains cost factors.
What details help the technician?
Share the model number from the indoor head label, when CH29 appears, the weather at the time, any unusual sounds and whether other codes have shown. Mention any past refrigerant work and recent storms.
How can you stay comfortable meanwhile?
Leave the system off once CH29 repeats. Use fans, blinds and water in summer, or a safe portable heater in winter. If anyone at home is vulnerable to temperature extremes, mention it when booking.
How can you lower the risk of phase faults?
- Keep the condenser coil clean and free of debris.
- Maintain clear airflow around the condenser unit.
- Book regular servicing so a technician can check terminals and pressures.
- Avoid switching the system on and off rapidly.
- Report unusual hums or vibrations early.
Our LG air conditioner service Sydney page explains what a service includes.
What does a burnt compressor terminal look like?
Under the terminal cover on top of the compressor, healthy connections look clean with intact insulation. A burnt terminal may show brown or black discolouration, melted plastic on the connector or a pitted metal pin. Sometimes the wire insulation near the terminal has hardened or cracked from heat. These signs suggest a poor connection has been heating for some time.
Repairing a burnt terminal involves replacing the connector. If the compressor pin also shows damage, the technician decides whether cleaning will do or whether the compressor itself needs attention. Catching this early prevents more serious damage.
Why does vibration matter for compressor wiring?
Compressors vibrate as they run, especially at start up and at certain speeds. Over years, that movement can work terminals loose or rub wire insulation against the cabinet. LG mounts compressors on rubber feet and secures wiring with clips to reduce this, yet age and poor installation can undo those protections. During a service, a technician checks that wiring sits securely and that mounting feet remain in good condition.
Can a multi split system show CH29?
Yes. A multi split relies on a single compressor in the condenser unit to serve every indoor head. When CH29 appears, all rooms lose cooling or heating together, and each display may show the code. Because multi split compressors often run harder when several rooms call at once, high load can play a bigger part. Consequently, the technician pays close attention to coil cleanliness, fan performance and refrigerant charge as well as the electrical tests.
How long does a CH29 repair take?
Simple fixes, such as replacing a burnt connector or cleaning a heavily blocked coil, often happen during the first visit. In contrast, board replacement depends on part availability for your model. Compressor replacement takes the longest, because it involves refrigerant recovery, brazing, a new filter drier, evacuation and a weighed charge. In that case, the technician usually books a dedicated visit once parts arrive.
What should you watch for after the repair?
Once the system runs again, listen to the condenser unit over the next few days. A smooth, steady hum is a good sign. Meanwhile, keep an eye on comfort and on the display. If any new code appears, or the old one returns, note the time and conditions and call back promptly.
LG CH29 error, booking help
The LG CH29 error means one or more compressor phases drew too much current. With winding tests, terminal checks and inverter testing, a technician can find out whether the problem lies in the compressor, the board or the operating conditions.
Writing down the date of each fault builds a useful history over time.
Patience during testing usually pays off with a more lasting repair.
Most faults are far easier to fix when they are caught early.
If several symptoms appear together, mention all of them rather than just the main one.
Technicians appreciate a clear path to both the indoor and outdoor units.
Call 02 9071 1142 or use our booking page to arrange an LG technician.
Frequently asked questions
What does CH29 mean on an LG?
It generally indicates overcurrent in one or more compressor output phases.
Is CH29 a dead compressor?
Not always. Terminals and inverter boards are frequent causes.
Can a dirty outdoor coil contribute to CH29?
Yes. Higher load raises current in every phase.
Why does my outdoor unit hum and stop?
A struggling compressor or phase fault can cause that pattern.
Should I keep restarting the system?
No. Repeated starts can damage the power module.
Is CH29 related to CH21?
Yes. Both involve current in the compressor drive.