LG CH06 Error, Making Sense of the Coil Outlet Probe

Most people never think about the far end of their indoor coil, yet LG watches it closely.

A probe on the outlet pipe tells the board how much work the refrigerant has done by the time it leaves the coil. If that probe stops making sense, the system halts and shows the LG CH06 error. This guide covers the job of the outlet probe, the usual culprits and the path to a fix.

What is the LG CH06 error?

In LG service information, CH06 is commonly listed as an indoor pipe outlet temperature sensor fault. Some manuals call it the evaporator outlet thermistor or the indoor discharge pipe sensor. Whatever the label, it sits on the copper tube where refrigerant leaves the indoor coil, and it reports temperature to the indoor board.

When the board reads a value that indicates a broken or shorted circuit, or a temperature far outside what the coil could reach, it stops trusting the sensor. At that point it shuts the system down and shows CH06 until someone resolves the problem.

Why have a sensor at both ends of the coil?

Picture refrigerant entering the coil as a cold mix of liquid and vapour. As it flows through the tubes and absorbs heat from room air, the liquid boils away. By the outlet, it should be entirely vapour and slightly warmer than at the inlet. That small temperature rise tells the system how effectively the coil is working.

LG uses the difference between inlet and outlet readings to fine tune the electronic expansion valve in the condenser unit. If the outlet runs too warm, the coil is starving and needs more refrigerant flow. If it runs too cold, liquid might be leaving the coil, which risks returning to the compressor. In short, the outlet probe helps balance efficiency and compressor safety.

SensorLocationMain role
CH02 inlet probeWhere refrigerant enters the coilFreeze and overheat protection, fan timing
CH06 outlet probeWhere refrigerant leaves the coilFlow balance and valve control

Because the two work as a pair, a fault in either one upsets the balance.

What might you notice before CH06 appears?

Outlet probe problems sometimes show up as subtle performance changes before any code.

  • Cooling feels weaker than usual, especially on hot afternoons.
  • Parts of the indoor coil sweat or frost unevenly.
  • The condenser unit seems to run harder than normal.
  • Comfort varies from day to day without any change in settings.
  • The code appears shortly after repair work or a coil clean.
  • A faint gurgling or hissing from the indoor head becomes more noticeable.

None of these prove a sensor fault, since refrigerant and airflow problems cause similar effects. Still, they are worth mentioning.

What typically goes wrong with the outlet probe?

The causes mirror those for other thermistors, though the location adds its own twist.

The probe itself fails

Constant condensation and temperature cycling slowly degrade the element. Eventually its resistance goes open, short or wildly inaccurate.

The probe works loose

The outlet tube often sits near the back or side of the coil, where access is tight. A probe disturbed during cleaning may sit loosely or fall out of its pocket entirely.

The lead gets damaged

Outlet sensor leads frequently run along the coil end plate, where sharp fin edges and metal brackets can cut insulation over time.

The connector corrodes

Like other indoor sensors, the outlet probe plugs into the board through a small connector that moisture can corrode.

The board input fails

In a small number of cases, the reading circuit on the board itself is at fault.

Is it safe to check anything yourself?

There is very little an owner can do directly with this sensor, since it sits deep inside the wall unit. Even so, a few general steps are sensible.

  • Switch off at the remote and then at the circuit breaker.
  • Remove and rinse the mesh filters if they look dusty.
  • Let any visible ice on the coil melt completely.
  • Restore power and restart the system once.

If CH06 returns, leave the system off and arrange a visit. Please do not remove the casing or disturb wiring inside the indoor head. Our LG reset guide explains the safe restart sequence.

How does a technician separate a sensor fault from a refrigerant fault?

This question sits at the heart of CH06 diagnosis. The technician starts by reading what the board sees, often through a diagnostic mode or service tool. Then they compare that with real measurements, such as a clamp thermometer on the outlet pipe and pressure gauges on the condenser unit.

If the board reading disagrees sharply with the real pipe temperature, the sensor or its circuit is faulty. If the board reading matches reality but the values themselves are abnormal, the problem lies elsewhere, such as low refrigerant, a stuck expansion valve or poor airflow.

Once they suspect the sensor, they unplug it and measure resistance, comparing it with the published value for the current temperature. They inspect the lead and connector carefully, then check the board input if the sensor tests well.

Which repairs clear CH06?

FindingUsual repair
Faulty outlet probeReplace the probe
Probe loose or missing from pocketRefit with good thermal contact
Cut or chafed leadRepair or replace the lead and protect it
Corroded connectorClean or replace the plug
Board input faultRepair or replace the indoor board
Refrigerant or valve issue found insteadRepair leak, recharge or service the valve

After the work, the technician confirms both coil sensors read sensibly and the system performs well in cooling and heating.

How does the expansion valve depend on this reading?

LG inverter systems use an electronic expansion valve, usually in the condenser unit, to meter refrigerant into the indoor coil. The board opens or closes this valve in small steps based on readings that include the outlet probe. If the outlet reading is wrong, the board might close the valve too far and starve the coil, or open it too far and flood it.

Either error reduces efficiency. A starved coil delivers less cooling, while a flooded coil risks liquid refrigerant returning to the compressor. Correcting a faulty probe therefore restores not just protection but efficiency too.

Could a dirty filter cause CH06?

A dirty filter will not usually trigger CH06 by itself, because the sensor still reports a real temperature. However, restricted airflow pushes coil temperatures to extremes, and combined with a marginal sensor, that can produce erratic readings. Keeping filters clean removes one variable from the picture. Our LG clean filters guide shows how.

Does CH06 affect heating as well as cooling?

Yes. In heating, the roles of the coil reverse and it becomes the condenser, releasing heat into the room. The outlet probe still helps the board judge refrigerant conditions and protect the system. A faulty probe can therefore affect heating comfort and may stop the system in winter as readily as in summer.

How common is CH06 compared with other sensor codes?

Outlet sensor faults are less frequent than room sensor faults on many systems, partly because the probe sits in a more protected spot. When they do happen, they often follow work inside the unit or long years in humid conditions. If nobody has ever opened your system and it is still relatively young, the technician may look harder at other causes before blaming the sensor.

What does the repair cost depend on?

Sensor replacement itself is modest. Costs depend more on access, since some LG indoor heads require partial dismantling to reach the outlet probe, and on whether a refrigerant problem is also present. Our LG AC repair cost Sydney page explains the general factors.

What information helps when you book?

Share the model number from the label on the indoor head, when CH06 first appeared, whether cooling or heating had been weak beforehand and whether anyone recently worked on the unit. Mention any ice, unusual sounds or drips.

What should you do while you wait?

Leave the system off once the code repeats, since the board cannot balance refrigerant flow safely. Keep cool with fans and blinds in summer, or warm with a safe portable heater in winter.

What does superheat mean in plain language?

Technicians often talk about superheat when discussing the outlet probe. It simply describes how much warmer the refrigerant vapour is than its boiling point by the time it leaves the coil. A small amount of superheat shows that all the liquid has boiled away and the coil is fully used. Too much superheat means the refrigerant boiled off early, leaving part of the coil doing little. Too little suggests liquid might still be present at the outlet.

LG uses the inlet and outlet probes together to estimate this value continuously. The board then adjusts the expansion valve to keep superheat in a healthy band. When the outlet probe misreports, the estimate goes wrong and the valve hunts back and forth or settles in the wrong position. That is why a faulty outlet probe can quietly reduce performance even before CH06 appears.

Can a multi split system show CH06 on only one head?

Yes. On a multi split, each indoor head carries its own coil sensors, while the condenser unit manages refrigerant to all of them. If only one room displays CH06, the fault almost certainly sits within that indoor head, its probe or its wiring. If several heads show odd behaviour together, the technician will look harder at shared parts outside, such as the expansion valves or the refrigerant charge.

What happens during the replacement?

Replacing an outlet probe usually involves isolating power, removing the front casing and sometimes the drain tray, then locating the probe on the outlet tube. The technician unclips the old probe, routes the new lead along the same path and secures it away from sharp edges. Thermal paste may go into the pocket to improve contact. After plugging it into the board and reassembling the unit, they run the system and compare readings with a reference thermometer.

How can you protect the sensors in your unit?

Regular, careful servicing helps the most. A technician who knows where each probe sits will shield it during coil cleaning, check its fit and confirm readings afterwards. Between visits, simply keep filters clean, run the fan briefly after cooling to dry the coil and report any unusual drips or noises early.

Why do technicians check the whole circuit before replacing the probe?

Replacing a sensor that is actually healthy wastes money and leaves the real fault in place. Because CH06 sits so close to refrigerant behaviour, a careful technician confirms the probe is genuinely faulty before swapping it. They look at pressures, compare both coil readings and inspect the expansion valve behaviour. Only when the evidence points clearly at the probe or its wiring do they replace it. This approach takes a little longer at the start, yet it avoids repeat visits and gives you confidence the repair will last.

LG CH06 error, booking help

The LG CH06 error means the board has lost a trustworthy reading from the indoor coil outlet. A technician can compare that reading with real measurements, decide whether the probe or the refrigerant circuit is at fault and put it right.

Older systems often still have plenty of life left when they receive steady care.

Keep furniture and curtains from blocking the airflow around the indoor unit.

A clean outdoor coil helps the whole system breathe more easily on hot days.

Call 02 9071 1142 or use our booking page to arrange an LG technician.

Frequently asked questions

What does CH06 mean on an LG?

It usually indicates a fault with the indoor coil outlet temperature sensor.

How is CH06 different from CH02?

CH02 generally covers the coil inlet probe, while CH06 covers the outlet probe.

Can low gas cause CH06?

Low gas causes abnormal readings, so testing must separate sensor and refrigerant faults.

Does CH06 affect heating?

Yes. The outlet probe supports control in both modes.

Can I fix CH06 at home?

No. The probe sits inside the unit and needs a technician.

Is the sensor expensive?

The part is modest. Access and any refrigerant work affect the total.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://lg.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, LG Service”,”url”:”https://lg.sydneyaircare.com.au/”,”description”:”LG air conditioner repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with LG.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”What does CH06 mean on an LG?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”It usually indicates a fault with the indoor coil outlet temperature sensor.”}},{“@type”:”Question”,”name”:”How is CH06 different from CH02?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”CH02 generally covers the coil inlet probe, while CH06 covers the outlet probe.”}},{“@type”:”Question”,”name”:”Can low gas cause CH06?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Low gas causes abnormal readings, so testing must separate sensor and refrigerant faults.”}},{“@type”:”Question”,”name”:”Does CH06 affect heating?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. The outlet probe supports control in both modes.”}},{“@type”:”Question”,”name”:”Can I fix CH06 at home?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”No. The probe sits inside the unit and needs a technician.”}},{“@type”:”Question”,”name”:”Is the sensor expensive?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”The part is modest. Access and any refrigerant work affect the total.”}}]}
Call 02 9071 1142