LG CH22 Error, Too Much Current Flowing to the Outdoor Unit

Your LG condenser unit keeps a constant eye on how much current it draws from the household supply.

When that figure climbs past a safe ceiling, the board cuts the compressor and the display shows the LG CH22 error. Think of it as a smart fuse that resets itself. The real question is what pushed the current so high, and this page walks through the usual answers.

What does CH22 indicate?

LG service references generally describe CH22 as a compressor overcurrent or input overcurrent error, often measured through a current transformer on the outdoor board. In plain terms, the board measures the current flowing into the outdoor unit or through the compressor circuit. If that current exceeds a programmed limit for a set time, the board decides something is wrong and stops the compressor before wiring or components overheat.

CH22 differs slightly from CH21. CH21 reacts to an instant spike inside the power module, while CH22 usually reacts to sustained high current. The causes overlap, yet the pattern of the fault gives the technician a useful hint about where to look.

Why does current rise in the first place?

Electrical current reflects how hard the compressor works. Under normal conditions, current rises when the system speeds up to meet demand and falls once the room settles. Several things can push it beyond normal levels.

  • Very high refrigerant pressures, which make the compressor work harder.
  • Mechanical wear inside the compressor, adding friction.
  • Electrical faults such as shorted windings or failing components.
  • Low supply voltage, which forces the unit to draw more current for the same power.
  • Overcharged refrigerant, which raises pressures.
  • A failing condenser fan, which leaves heat trapped in the coil.

The board cannot tell which of these caused the rise. It only knows the current is too high, so it protects the system and leaves the detective work to a technician.

What symptoms usually come with CH22?

Owners often notice a pattern rather than a single event.

  • The condenser unit runs for a while, then stops abruptly.
  • The fault appears most during the hottest part of the day.
  • Breakers trip occasionally when the system is under heavy load.
  • The outdoor coil looks dirty or blocked with leaves.
  • The condenser fan sounds weak, noisy or slow.
  • Cooling drops off before the code appears.

Make notes on timing and conditions. A CH22 that only appears in heatwaves tells a different story from one that appears at every start.

Which faults commonly trigger CH22?

Dirty or blocked condenser coil

This is one of the most common causes, especially in summer. When dust, leaves or salt coat the outdoor coil, heat cannot escape. Pressures and current climb together. Cleaning the coil often resolves the problem completely.

Weak or failing outdoor fan

A fan that spins slowly moves less air across the coil, producing the same effect as a dirty coil. Worn bearings, a tired motor or a failing capacitor on older designs can all slow the fan.

Refrigerant overcharge or non condensables

If too much refrigerant went in during a past repair, or air entered the system because evacuation was poor, pressures run high. The compressor draws more current as a result.

Compressor wear

Worn bearings, damaged valves or internal friction increase the effort needed to turn the compressor. Current rises steadily with wear until the board steps in.

Electrical faults

Partially shorted windings, failing inverter components or damaged wiring can all raise current. Loose terminals heat up and create resistance, which also distorts readings.

Supply problems

A weak supply, perhaps from undersized cabling, a failing breaker or a loose neutral at the switchboard, reduces voltage at the condenser unit. To deliver the same power, the unit draws more current.

Faulty current sensor

Occasionally, the current transformer or its circuit on the board fails and reports a high value that is not real. Testing reveals whether the measured current matches the reading.

What can an owner safely check?

A few checks are safe and sometimes helpful.

  • Look at the outdoor coil from a safe distance for leaves, dust or debris.
  • Clear plants, bins and stored items away from the condenser unit.
  • With the system off at the isolator, gently remove loose leaves from the coil face by hand.
  • Check whether the condenser fan turns freely when running, from a safe distance.
  • Note whether breakers have tripped and reset them once if safe.
  • Restart the system once and observe how long it runs.

If CH22 returns quickly, leave the system off and book a visit. Our LG outdoor unit check guide explains what to look for around the condenser unit.

Do not hose the coil with high pressure water, open panels or attempt electrical checks yourself.

How does a technician diagnose CH22?

The technician approaches CH22 by measuring rather than guessing. First, they check the supply voltage at the condenser unit, both at rest and while the compressor runs. A large drop under load points to supply problems.

Next, they measure actual current with a clamp meter and compare it with the reading the board reports. If the two differ significantly, the current sensor or board may be faulty. If they match, the high current is real.

Then they examine operating conditions. Pressure gauges show whether high side pressure is abnormal. They inspect the coil, fan and airflow, and check refrigerant charge if pressures look wrong.

After that, they test the compressor windings for balance and insulation, and inspect the inverter board and wiring for heat damage or loose terminals.

Finally, they piece together the evidence. A dirty coil plus high pressure plus normal windings points one way. Balanced pressures plus abnormal windings point another.

Which repairs typically clear CH22?

FindingTypical repair
Dirty condenser coilThorough coil clean
Weak outdoor fanReplace motor or capacitor
Refrigerant overchargeRecover and weigh in the correct charge
Air in the systemRecover, evacuate and recharge properly
Loose or burnt terminalsRepair wiring and connections
Supply voltage problemLicensed electrician repairs the supply
Faulty current sensor or boardReplace the outdoor board
Worn compressorReplace the compressor

After repairs, the technician runs the system under load and confirms current stays within normal limits across a range of speeds.

Why does CH22 show up in heatwaves?

On scorching afternoons, the condenser unit must reject heat into air that is already very hot. Pressures rise naturally, and so does current. A system with a slightly dirty coil or a marginal fan may cope on mild days, then cross the limit once temperatures soar. That is why CH22 often clusters on the hottest days of summer, particularly in western suburbs.

Shade that leaves airflow clear, a clean coil and a healthy fan give the system more headroom. Our LG air conditioner turns off by itself guide covers heat related shutdowns more broadly.

Can CH22 appear in heating mode?

Yes, although less often in Sydney. In heating, the indoor coil becomes the condenser. If indoor airflow is poor because of dirty filters or a weak indoor fan, pressures and current rise. Cleaning filters and checking the indoor fan can help. A technician will consider both indoor and outdoor airflow when CH22 appears in winter.

How does CH22 relate to other compressor codes?

LG uses several related codes. CH21 covers instant DC peaks in the power module, CH26 covers rotor position faults and CH29 covers phase overcurrent. CH22 overlaps with all of them because high current can result from many of the same causes. Our LG CH21 error and LG CH29 error pages explain the related codes.

Is it safe to keep running the system?

Not once CH22 repeats. Each time the compressor runs at excessive current, wiring heats up, insulation ages and the compressor wears faster. A single restart after cleaning debris is reasonable. Beyond that, leave the system off and book a visit.

What details help the technician?

Share the model number from the indoor head label, when CH22 appears, the weather at the time, whether breakers trip and whether anyone has added refrigerant recently. Photos of the condenser unit and its surroundings help too.

How can you keep comfortable meanwhile?

Close blinds early, use fans and keep doors closed in summer. In winter, use a safe portable heater. If anyone in the home is vulnerable to heat, mention it when booking.

How can you prevent CH22 returning?

  • Keep the condenser coil clean, especially near trees or the coast.
  • Maintain clear space around the condenser unit.
  • Rinse indoor filters regularly so airflow stays strong in heating.
  • Book servicing before summer so a technician can check the fan and coil.
  • Report weak cooling early, before current climbs to the limit.

Our LG air conditioner service Sydney page explains what a routine visit includes.

How does a current transformer measure the load?

A current transformer is a small ring of magnetic material wrapped with fine wire. One of the supply conductors passes through the middle. As current flows, it creates a magnetic field that induces a tiny, proportional signal in the fine winding. The outdoor board reads that signal and converts it into a current figure.

This arrangement lets the board monitor heavy currents without any direct connection to them. It is reliable, yet not immune to faults. A cracked solder joint, a damaged lead or a failing component in the reading circuit can distort the figure. That is why a technician always compares the board reading with an independent clamp meter before deciding the high current is real.

What part does the supply cable play?

The cable from your switchboard to the condenser unit must suit the current the system draws. If it is too thin for the run length, or a joint along the way has loosened, voltage drops when the compressor speeds up. Lower voltage forces higher current, which can push the system toward CH22 during peak demand.

Signs of a supply issue include lights dimming when the air conditioner starts, a warm isolator switch or breakers that trip in hot weather. If the technician suspects the supply, they will recommend a licensed electrician to inspect the circuit, the breaker and the connections at the switchboard.

What about past refrigerant work?

If CH22 began soon after someone added gas, the charge deserves a close look. Overfilling raises condensing pressure and current. Equally, a recharge done without proper evacuation can leave air or moisture inside, which behaves like extra pressure in the system. The cure is to recover the refrigerant, pull a deep vacuum and weigh in the correct factory charge. Our LG aircon regas Sydney page explains how that process should work.

Can a multi split cause CH22 more easily?

Multi split condenser units run larger compressors to serve several rooms. When every indoor head calls for cooling on a hot afternoon, the compressor works at full output and current runs high. Any extra burden, such as a dirty coil, then pushes it over the limit more quickly than on a smaller single split. Keeping the coil spotless matters even more on these systems.

LG CH22 error, booking help

The LG CH22 error means current climbed too high and the board stepped in. With measurements of supply, current, pressure and windings, a technician can pinpoint the cause and fix it so the system runs within safe limits again.

A system that runs quietly and evenly is usually a system in good health.

Checking the drain outlet now and then confirms that water flows freely outside.

Even a short note about what changed recently can point straight to the cause.

Good airflow indoors and outdoors is the foundation of efficient performance.

Call 02 9071 1142 or use our booking page to arrange an LG technician.

Frequently asked questions

What does CH22 mean on an LG?

It generally indicates overcurrent in the outdoor unit supply or compressor circuit.

Can a dirty outdoor coil cause CH22?

Yes. Blocked coils raise pressure and current.

Why does CH22 appear on hot days?

Higher outdoor temperatures raise pressures and current.

Is CH22 a compressor failure?

Not always. Coils, fans, charge and supply are common causes.

Can low voltage trigger CH22?

Yes. A weak supply forces the unit to draw more current.

Should I keep restarting the system?

No. Restart once after clearing debris, then book a visit if it returns.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://lg.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, LG Service”,”url”:”https://lg.sydneyaircare.com.au/”,”description”:”LG air conditioner repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with LG.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”What does CH22 mean on an LG?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”It generally indicates overcurrent in the outdoor unit supply or compressor circuit.”}},{“@type”:”Question”,”name”:”Can a dirty outdoor coil cause CH22?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. Blocked coils raise pressure and current.”}},{“@type”:”Question”,”name”:”Why does CH22 appear on hot days?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Higher outdoor temperatures raise pressures and current.”}},{“@type”:”Question”,”name”:”Is CH22 a compressor failure?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Not always. Coils, fans, charge and supply are common causes.”}},{“@type”:”Question”,”name”:”Can low voltage trigger CH22?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes. A weak supply forces the unit to draw more current.”}},{“@type”:”Question”,”name”:”Should I keep restarting the system?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”No. Restart once after clearing debris, then book a visit if it returns.”}}]}
Call 02 9071 1142