LG CH38 Error, What a Low Refrigerant Warning Means

Refrigerant is the working fluid that carries heat between your rooms and the outdoors.

An LG system holds a fixed charge that should never need topping up. So when the board calculates that something is missing and shows the LG CH38 error, it is telling you a leak or a flow problem probably exists. Here is what the code means, why a quick top up is not the answer and how the fault gets fixed properly.

What does CH38 indicate on an LG?

LG service literature generally lists CH38 as a refrigerant leakage or low refrigerant detection error. The system does not measure the gas directly. Instead, it compares readings from several sensors, such as indoor pipe temperatures, outdoor coil temperature, discharge temperature and compressor current. When those readings form a pattern that matches a shortage of refrigerant, the board stops the system and records CH38.

Because the detection relies on calculations, CH38 can occasionally appear for related reasons, such as a blocked filter drier, a stuck expansion valve or a faulty sensor reporting wrong values. That is why testing always comes before any refilling.

Why does refrigerant matter so much?

A split system moves heat by changing refrigerant from liquid to vapour and back again. In cooling mode, the indoor coil absorbs heat from room air as the refrigerant evaporates. Outside, the compressor squeezes that vapour, the condenser coil releases the heat and the refrigerant becomes liquid once more. In heating mode, the process runs in reverse.

When the charge drops, less refrigerant circulates. The indoor coil gets colder than it should in some spots and warmer in others, capacity falls, and the compressor runs hotter because returning gas no longer cools it properly. Left alone, a shortage can shorten compressor life considerably.

Which warning signs come before or with CH38?

Low refrigerant rarely appears out of nowhere. Owners often notice a gradual decline first.

  • Cooling feels weaker each week, even on the lowest set point.
  • Heating takes far longer to warm the room in winter.
  • Frost or ice forms on the indoor coil or the thin copper line outside.
  • A faint hiss or bubbling sound comes from pipework.
  • Oily stains appear around pipe joints or on the condenser unit.
  • Power bills creep up while comfort goes down.

If you have seen several of these over recent weeks, CH38 is likely the end point of a slow leak.

Where do LG systems usually leak?

Leaks occur wherever copper, joints and seals live under pressure. Technicians often find them in these places.

Flare joints

Pipes connect to each unit with flared fittings tightened onto threaded connectors. Over years of heating and cooling cycles, poorly made or under tightened flares can loosen and seep.

Service valves

The valves on the condenser unit carry caps and cores that seal the system. Missing caps or worn cores allow slow leaks.

Coils

Indoor coils can develop pinhole leaks through chemical corrosion over time. Outdoor coils near the coast suffer salt corrosion. Both types of leak can be tiny and hard to find.

Pipe rub points

Pipes that vibrate against brackets, walls or each other gradually wear through. This is common where support is poor or where the condenser unit sits on a soft base that moves.

Accidental damage

Renovations, garden work and even hanging items on exposed pipes can puncture or crush lines.

Why is a simple gas top up a bad idea?

Topping up without finding the leak treats the symptom and leaves the cause untouched. The new refrigerant will escape too, often within months, and you pay for the same visit again. Meanwhile, the compressor keeps running in poor conditions during the decline.

There is also an accuracy problem. Without knowing exactly how much gas remains, a technician cannot add the correct amount. Too little leaves the system underperforming, while too much raises pressures and stresses components. The reliable approach involves recovering what remains, repairing the leak, pulling a deep vacuum and then weighing in the full factory charge.

Finally, Australian rules require licensed handling of refrigerants, partly to protect the environment from avoidable releases. Our LG aircon regas Sydney page explains the full process.

What can you safely do when CH38 appears?

There is little an owner can fix with a refrigerant fault, yet a few actions help.

  • Switch the system off so the compressor does not keep running short of gas.
  • Look for ice on the indoor coil or outdoor pipes and let it thaw naturally.
  • Check the mesh filters and rinse them if they look dusty, since poor airflow can mimic low gas symptoms.
  • Note any hissing, oily stains or recent work near the pipes.
  • Take photos of frost, stains and the display for the technician.

After cleaning the filters and letting any ice melt, you can try one restart. If CH38 returns, leave the system off and book a visit. Do not attempt to open valves, tighten fittings or add refrigerant yourself.

How does a technician confirm and locate the leak?

The visit usually begins with gauges connected to the service port. The technician compares pressures and temperatures with what a healthy system shows at the current conditions. They also check sensor readings, since a faulty sensor could trigger CH38 falsely.

Once the readings confirm a low charge, the hunt begins. First comes a careful visual inspection for oily residue at joints, valves and coil bends. Next, an electronic detector sniffs along pipes and coils. Bubble solution confirms suspect spots. When the leak hides well, the technician may recover the remaining refrigerant and pressurise the system with dry nitrogen, then watch for a pressure drop and search again.

On systems with concealed pipe runs, they may isolate sections to narrow down the location before deciding whether to open a wall or run a new line.

What repairs usually clear CH38?

The fix depends on where the leak sits and how bad it is.

Leak locationCommon repair
Flare jointCut and remake the flare, tighten to correct torque
Service valveReplace the core, cap or valve
Pipe rub pointReplace the section and add proper support
Indoor coil pinholesReplace the indoor coil
Outdoor coil corrosionRepair if possible, otherwise replace the coil
Hidden line damageRepair in place or run a new line

After the repair, the technician pressure tests with nitrogen, evacuates the system with a vacuum pump and weighs in the correct charge. Then they run the system and confirm temperatures, pressures and current draw.

Could something other than a leak trigger CH38?

Yes, occasionally. Because LG infers the refrigerant level from sensor data, other faults can look like a shortage. A blocked filter drier or strainer restricts flow. An electronic expansion valve that sticks closed starves the indoor coil. A sensor that reads incorrectly may convince the board that conditions are abnormal. A good technician checks these possibilities before assuming a leak.

Which refrigerant does your LG use?

Many recent LG split systems use R32, while older models commonly use R410A. The rating label on the condenser unit lists the refrigerant type and factory charge. Nobody should ever mix refrigerants, so the technician always confirms the type before any work.

Is CH38 worth repairing on an older system?

That depends on the leak and the overall condition of the unit. A loose flare on a healthy system is usually well worth fixing. An indoor coil riddled with pinholes on an older system with other worn parts may tip the balance toward replacement. Ask the technician to explain both options and their likely life expectancy. Our LG AC repair cost Sydney page outlines what shapes repair costs.

How long can a leak go unnoticed?

Slow leaks can take a long time to show obvious symptoms. A system might lose a small amount each season, with comfort sliding so gradually that nobody notices until a hot spell exposes the shortfall. That is why regular servicing helps. During a service, a technician can spot oily stains, frost patterns and unusual readings before the board ever raises CH38.

Does CH38 relate to freezing up?

Often. When refrigerant runs low in cooling mode, pressure in the indoor coil drops and the coil temperature falls below freezing. Moisture from the air then turns to ice on the fins. As ice spreads, airflow drops and the problem accelerates. Our LG air conditioner freezing up guide explains the full picture.

What should you tell the technician?

Mention when cooling or heating first seemed weaker, whether you saw ice or heard hissing, whether anyone has added gas before and whether any renovation or garden work happened near the pipes. A history of past top ups strongly suggests an ongoing leak, so that detail matters.

How can you stay comfortable meanwhile?

Leave the system off once CH38 repeats. Draw blinds, use fans and keep hydrated in summer, or use a safe portable heater in winter. If anyone in the household is vulnerable to heat or cold, mention it when booking so the team understands the urgency.

How does low gas affect each season?

The effects shift with the weather. In summer, a short charge means weak cooling, long running times and possibly ice on the indoor coil. Rooms feel stuffy rather than cold, and the condenser unit may run without pause on hot afternoons.

In winter, heating suffers in a similar way. Air from the indoor head feels lukewarm, warm up takes ages and the outdoor coil may frost over more often, triggering frequent defrost cycles. Because Sydney winters are mild compared with many places, some owners only notice the problem when the first proper cold snap arrives.

Either way, the system works harder for less comfort, and that extra strain falls on the compressor.

Why does the compressor suffer when gas runs low?

The compressor relies on returning refrigerant vapour to keep its motor cool and to carry lubricating oil back from the pipes. When the charge drops, less vapour returns, the motor runs hotter and oil may linger in the coils instead of returning. Over time, that combination wears bearings and windings.

LG inverter systems monitor discharge temperature and current to protect the compressor, and CH38 is part of that protection. Even so, a system that ran short for many weeks before the code appeared may already have suffered some wear. That is another reason to act quickly once comfort starts to slip.

How do multi split systems handle CH38?

On a multi split, several indoor heads share one charge of refrigerant held mainly in the condenser unit. A leak on any branch drains the whole system, so every room may lose capacity together. Finding the leak can take longer because there are more joints and longer pipe runs. Technicians often test each branch separately with nitrogen to pinpoint the culprit before repairing it.

What happens after the repair?

Once the leak is fixed and the system refilled by weight, comfort should return quickly. The indoor coil cools evenly, frost disappears and the condenser unit settles into a steady rhythm. Ask the technician to note the repair location and the charge added on your invoice. That record helps if questions ever arise later.

LG CH38 error, booking help

The LG CH38 error is a clear signal to find out why refrigerant is missing. A licensed technician can confirm the shortage, locate and repair the leak, then refill by weight so your LG performs as designed.

Fresh batteries in the remote rule out one of the most common false alarms.

It helps to know whether the problem affects one room or every room in the home.

Call 02 9071 1142 or use our booking page to arrange an LG technician.

Frequently asked questions

What does CH38 mean on an LG?

It generally indicates low refrigerant or a suspected leak.

Can I just top up the gas?

A top up without a leak repair only delays the problem and must be done by a licensed technician.

Why is there ice on my LG pipes?

Low refrigerant often causes freezing, although dirty filters can too.

Can a faulty sensor cause CH38?

Yes, occasionally. Testing confirms whether gas is actually low.

Which refrigerant does my LG use?

Check the condenser label. Many recent models use R32.

Is it safe to keep using the system?

No. Running short of gas stresses the compressor.

{“@context”:”https://schema.org”,”@type”:”HVACBusiness”,”@id”:”https://lg.sydneyaircare.com.au/#business”,”name”:”Sydney Air Care, LG Service”,”url”:”https://lg.sydneyaircare.com.au/”,”description”:”LG air conditioner repair, service and troubleshooting across Sydney. Independent service provider, not affiliated with LG.”,”areaServed”:[{“@type”:”City”,”name”:”Sydney”},{“@type”:”State”,”name”:”New South Wales”}],”parentOrganization”:{“@type”:”Organization”,”name”:”Sydney Air Care”,”url”:”https://sydneyaircare.com.au/”},”telephone”:”+61 2 9071 1142″} {“@context”:”https://schema.org”,”@type”:”FAQPage”,”mainEntity”:[{“@type”:”Question”,”name”:”What does CH38 mean on an LG?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”It generally indicates low refrigerant or a suspected leak.”}},{“@type”:”Question”,”name”:”Can I just top up the gas?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”A top up without a leak repair only delays the problem and must be done by a licensed technician.”}},{“@type”:”Question”,”name”:”Why is there ice on my LG pipes?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Low refrigerant often causes freezing, although dirty filters can too.”}},{“@type”:”Question”,”name”:”Can a faulty sensor cause CH38?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Yes, occasionally. Testing confirms whether gas is actually low.”}},{“@type”:”Question”,”name”:”Which refrigerant does my LG use?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”Check the condenser label. Many recent models use R32.”}},{“@type”:”Question”,”name”:”Is it safe to keep using the system?”,”acceptedAnswer”:{“@type”:”Answer”,”text”:”No. Running short of gas stresses the compressor.”}}]}
Call 02 9071 1142